| 10/07/2008 |
| Laval, QC Canada
- J.D. Irving in St-Leonard, New Brunswick, has upgraded their canter from a competing knife system to Iggesund’s Variable Geometry Head with TurnKnife III (VGH). With this cutting edge technology, the mill has seen their chip quality jump by 5% as well as a net improvement of the board finish due to a reduction in knife line deviation.
|
| |
| 10/07/2008 |
| Laval, QC Canada
- Bois Cèdrico in Causapscal, Quebec, has purchased a new canter for which they requested Iggesund’s Helical Solid Heads with TurnKnife III (HSH). The superior chip quality and board finish obtained with the HSH motivated the selection of this product.
|
| |
| 10/07/2008 |
| Laval, QC Canada
- Bois Daaquam in St-Just-de-Bretenières, Quebec has replaced a competing reversible knife system installed in their canter with Iggesund’s Helical Solid Head with TurnKnife III (HSH). Improvements to the chip quality and board finish (tear depth reduction) were reported by the mill. In addition, a longer knife life was also noted by the personnel.
|
| |
| 10/07/2008 |
| Laval, QC Canada
- Abitibi-Consolidated in Girardville, Quebec, an Iggessund Tools PartnerChip Program customer, has recently upgraded their canter to Iggesund’s Helical Solid Head with TurnKnife III (HSH). Improved board finish and more uniform chips are a few of the benefits provided by this technology.
|
| |
| 10/07/2008 |
| Laval, QC Canada
- Matériaux Blanchet in Amos, Quebec, has replaced the reversible knife system running in their DDM machine with Iggesund’s Helical Solid Head with TurnKnife III (HSH). The machine production was increased by at least 10%, while reducing fibre tear-out and eliminating weekly maintenance.
|
| |
| 07/21/2008 |
| Laval, QC Canada
- Lakeland Mills in Prince George, British Columbia has recently completed a 90-day evaluation of Iggesund’s TurnKnife III for Drum Heads (TKD) in their CM&E End Dogging machine. TKD has proven to produce superior chips and a more uniform board finish. Lakeland has also placed an order for 2 Variable Geometry Heads with TurnKnife III heads (VGH) for this machine. |
| |
| 06/02/2008 |
| Laval, QC Canada
- Weyerhaeuser in Princeton, British Columbia has upgraded one more chipping head to Iggesund’s TurnKnife III technology. After a few months of operation, this mill has reported improved reliability and chip quality at increased line speeds, while a reduced required maintenance was noted. |
| |
| 06/02/2008 |
| Laval, QC Canada
- Tolko Industries in Kelowna, British Columbia has completed the start-up of their brand new Comact DDM line equipped with Iggesund’s Helical Solid Heads (HSH) and TurnKnife III profiler heads. The mill has noted an exceptional surface finish, as well as, record lumber production figures. |
| |
| 06/02/2008 |
| Laval, QC Canada
- Rivercity in Kamloops, British Columbia has equipped their Precision chipper with Iggesund’s renowned TurnKnife II technology. Increased production and chip quality are just a few of the benefits provided by this system. |
| |
| 06/02/2008 |
| Laval, QC Canada
- Domtar Forest Products in Timmins, Ontario has converted their Optimil Jumbo line to Iggesund’s TurnKnife III technology with VFDs (variable frequency drives. With the Variable Geometry (VGH) and TurnKnife III for Drum Heads (TKD), the mill has reported back an impressive chip quality improvement along with an increased knife life and reduced maintenance. Additionally, knife movements was eliminated with the TurnKnife III multi-spline bottom head. |
| |
